Authentic Best resources for JN0-362 Test Engine Practice Exam
[2021] JN0-362 PDF Questions - Perfect Prospect To Go With GuideTorrent Practice Exam
Who should take the JN0-362 exam
This exam is intended for learners who are pursuing routing and switching technologies and related platform configuration and troubleshooting skills.
NEW QUESTION 19
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The configuration is for an internal BGP session
- B. The local-address statement is not required for the BGP session to establish correctly
- C. The local-address statement is required for the BGP session to establish correctly
- D. The configuration is for an external BGP session
Answer: A,C
NEW QUESTION 20
Click the Exhibit.
You have just configured IS-IS, but the adjacency is not coming up.
Referring to the exhibit, what is the cause?
- A. Only one side is configured using the point-to-point parameter.
- B. The family iso parameters is missing on the interfaces.
- C. One router is configured for Level 2 only.
- D. The routers must be in different areas.
Answer: A
NEW QUESTION 21
You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisition.Which statement is correct about this scenario?
- A. Type 5 LSAs would be seen only in the newly attached area.
- B. Type 5 LSAs would be blocked in a stub area.
- C. Type 5 LSAs would carry external information across your transit area to the backbone.
- D. Type 5 LSAs would be converted to type 7 LSAs.
Answer: B
NEW QUESTION 22
Click the Exhibit button.
You must create a static route on Router-A to the 10.10.5.0/24 network using 10.10.3.2 as the next hop.
Referring to the exhibit, which configuration accomplishes this task?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION 23
Click the Exhibit button. You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required that an IS-IS adjacency be established without the need for a designated intermediate system (DIS)
Which configuration statement entered on both routers will achieve this goal?
- A. set interface ge-0/0/2 unit 0 family iso point-to-point
- B. set protocols isis interface ge-0/0/2.0 point-to-point
- C. set protocols isis interface ge-0/0/2.0 no-dis
- D. set interface ge-0/0/2 unit 0 family iso no-dis
Answer: B
NEW QUESTION 24
An IS-IS level 1-only router is configured within a larger multilevel hierarchy. Which OSPF area type resembles the routing information in the L1 router's table?
- A. OSPF NSSA with no summaries
- B. OSPF default area
- C. OSPF NSSA
- D. OSPF stub area
Answer: A
NEW QUESTION 25
Click the Exhibit.
You have configured the IBGP group shown in the exhibit. However, committing your configuration fails.
Which parameter should you add to the IBGP group configuration to correct the problem?
- A. Type internal
- B. As -override
- C. Export <policy name>
- D. Type external
Answer: A
NEW QUESTION 26
Click the Exhibit.
Referring to the exhibit, what is the result of applying this policy?
- A. The 172.18.1.1/32 prefix will be redistributed into OSPF as an external route.
- B. The 172.18.1.0/24 prefix will be redistributed into OSPF as an internal route.
- C. The 172.18.1.0/24 prefix will be redistributed into OSPF as an external route.
- D. The 172.18.1.1/32 prefix will be redistributed into OSPF as an internal route.
Answer: C
NEW QUESTION 27
Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. The router will install the 0.0.0.0/0 route into the routing table when no BGP prefixes are present
- B. The router will remove the 0.0.0.0/0 route from the routing table when no BGP prefixes are present
- C. The router will remove the 0.0.0.0/0 route from the routing table when any BGP prefixes are present
- D. The router will install the 0.0.0.0/0 route into the routing table when any BGP prefixes are present
Answer: B,D
NEW QUESTION 28
Click the Exhibit button.
Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?
- A. the multicast address
- B. the link-local address
- C. the loopback address
- D. the statically assigned address
Answer: B
NEW QUESTION 29
You have just configured IPv6 in your network. A packet arrives on your router that exceeds the MTU size. How will an IPv6 router respond?
- A. The packet is kept intact and not fragmented.
- B. The packet is dropped.
- C. The fragment offset is referenced and the packet is fragmented.
- D. The packet is fragmented based on extension headers.
Answer: B
NEW QUESTION 30
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would like to ping the remotely connected CE router's loopback address. The address of the loopback is
122.161.2.1, the VPN routing-instance is called VPN-C.Which command will accomplish this goal?
- A. ping vpn-instance VPN-C 122.161.2.1
- B. ping VPN-C 122.161.2.1
- C. ping routing-instance VPN-C 122.161.2.1
- D. ping instance VPN-C 122.161.2.1
Answer: C
NEW QUESTION 31
Which statement is true regarding default MPLS label handling?
- A. A router that pops a label from a label stack applies class of service based on the IP header to ToS bits.
- B. A router that pops a label from a label stack forwards a frame based on the underlying destination IP address.
- C. A router that pops a label from a label stack forwards a frame based on the label that was popped.
- D. A router that pops a label from a label stack always pushes a new label on the packet
Answer: B
NEW QUESTION 32
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The BGP peering between R1 and R4 should use loopback interface addresses
- B. The BGP peering between R1 and R4 should use physical interface addresses
- C. The BGP peerings between R1, R2, and R3 should use physical interface addresses
- D. The BGP peerings between R1, R2, and R3 should use loopback interface addresses
Answer: B,D
NEW QUESTION 33
What is the size of the unique address used to identify each node on an Ethernet LAN?
- A. 9 bytes
- B. 12 bytes
- C. 6 bytes
- D. 3 bytes
Answer: C
NEW QUESTION 34
......
How to study the JN0-362 Exam
A solid foundation on Multiprotocol Label Switching (MPLS) is required. After beginner concepts such as MPLS forwarding and the structure of the MPLS header, you should learn into the configuration and operation of the two main label distribution protocols, RSVP and LDP. Give special emphasis to the central topics of traffic engineering and MPLS traffic protection, including fast reroute, link/node protection, and LDP loop-free alternate. Put into practice with a series of in-depth hands-on labs, which will allow candidate to gain experience in configuring and monitoring MPLS on Junos OS devices. Utilize Juniper Networks vMX Series devices using the Junos OS Release 16.1R3.10, but are also applicable to other MX Series devices.JN0-362 practice exams provides detailed resources and items on the JN0-362 exam. The JN0-362 dumps will help you identify the content and difficulty level of the questions and the practice Exams will make you familiar with the format and environment of an exam. You should refer this JN0-362 dumps carefully before attempting your actual exam.
Best updated resource for JN0-362 Online Practice Exam: https://www.guidetorrent.com/JN0-362-pdf-free-download.html