Updated May 05, 2024 Verified 300-410 dumps Q&As - 100% Pass
New 2024 Latest Questions 300-410 Dumps - Use Updated Cisco Exam
NEW QUESTION # 325
Refer to the exhibit.
Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed
Answer:
Explanation:
NEW QUESTION # 326
Refer to the exhibit.
The control plane is heavily impacted after the CoPP configuration is applied to the router. Which command removal lessens the impact on the control plane?
- A. access-list 120 permit ospf any
- B. access-list 120 permit tcp any gt 1024 eq bgp log
- C. access-list 120 permit udp any any eq pim-auto-rp
- D. access-list 120 permit eigrp any host 224.0.0.10
Answer: C
NEW QUESTION # 327
Refer to the exhibit.
After a security audit, the administrator implemented an ACL in the route reflector. The RR became unreachable from any router in the network. Which two actions resolve the issue? (Choose two.)
- A. Change the next hop of the default route to the link-local address of the default gateway.
- B. Remove the ACL entry 80.
- C. Permit ICMPv6 neighbor discovery traffic in the ACL.
- D. Configure a link-local address on the Ethernet0/1 interface.
- E. Enable the ND proxy feature on the default gateway.
Answer: B,C
NEW QUESTION # 328
An engineer is trying to copy an IOS file from one router to another router by using TFTP.
Which two actions are needed to allow the file to copy? (Choose two.)
- A. Copy the file to the destination router with the copy tftp: flash: command
- B. Configure a user on the source router with the username tftp password tftp command.
- C. Enable the TFTP server on the source router with the tftp-server flash:<filename> command.
- D. Configure the TFTP authentication on the source router with the tftp-server authentication local command.
- E. TFTP is not supported in recent IOS versions, so an alternative method must be used.
Answer: A,C
NEW QUESTION # 329
Refer to the exhibit.
Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements:
Host1 must use the FTP1 fileserver.
Host2 must use the FTP2 fileserver.
Which configuration meets the requirement on R1?
- A.
- B.
- C.
- D.
Answer: A
NEW QUESTION # 330
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?
- A. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.
- B. The summary route is visible only in the OSPF database, not in the routing table.
- C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
- D. The summary-address command is used only for summarizing prefixes between areas.
Answer: C
Explanation:
Explanation
The summary-address is only used to create aggregate addresses for OSPF at an autonomous system boundary.
It means this command should only be used on the ASBR when you are trying to summarize externally redistributed routes from another protocol domain or you have a NSSA area. But a requirement to create a summarized route is:
The ASBR compares the summary route's range of addresses with all routes redistributed into OSPF on that ASBR to find any subordinate subnets (subnets that sit inside the summary route range). If at least one subordinate subnet exists, the ASBR advertises the summary route.
NEW QUESTION # 331
Refer to the exhibit.
An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
- A. Configure the service timestamps log datetime localtime command in global configuration mode.
- B. Configure the logging clock synchronize command in global configuration mode.
- C. Configure the service timestamps log uptime command in global configuration mode.
- D. Make sure that the clock on the device is synchronized with an NTP server.
Answer: C
Explanation:
Explanation
https://community.cisco.com/t5/networking-documents/router-log-timestamp-entries-are-different-from-the-syste
NEW QUESTION # 332
Refer to the exhibit. What is the result of applying this configuration?
- A. The router can form BGP neighborships with any device that is matched by the access list named "BGP".
- B. The router can form BGP neighborships with any other device.
- C. The router cannot form BGP neighborships with any device that is matched by the access list named
"BGP". - D. The router cannot form BGP neighborships with any other device.
Answer: B
Explanation:
Section: Layer 3 Technologies
NEW QUESTION # 333
Refer to the exhibit.
To provide reachability to network 10.1.1.0 /24 from R5, the network administrator redistributes EIGRP into OSPF on R3 but notices that R4 is now taking a ........... path through R5 to reach 10.1.1.0/24 network. Which action fixes the issue while keeping the reachability from R5 to 10.1.1.0/24 network?
- A. Apply the outbound distribution list on R5 toward R4 in OSPF.
- B. Change the administrative distance of OSPF to 200 on R5.
- C. Redistribute OSPF into EIGRP on R4
- D. Change the administrative distance of the external EIGRP to 90.
Answer: D
NEW QUESTION # 334
Refer to the exhibit. An engineer must establish multipoint GRE tunnels between hub router R6 and branch routers R1, R2, and R3. Which configuration accomplishes this task on R1?
A)
B)
C)
D)
- A. Option A
- B. Option D
- C. Option C
- D. Option B
Answer: B
NEW QUESTION # 335
Refer to the exhibit.
ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?
- A. Start-time now
- B. Start-time immediately
- C. Start-time 0
- D. Start-time 00:00
Answer: A
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/sla_icmp_echo.html
NEW QUESTION # 336
Which protocol does MPLS use to support traffic engineering?
- A. Label Distribution Protocol
- B. Resource Reservation Protocol
- C. Tag Distribution Protocol
- D. Border Gateway Protocol
Answer: B
Explanation:
NEW QUESTION # 337
Which two statements about troubleshooting with Unicast reverse Path Forwarding are true? (Choose two.)
- A. Cisco Express Forwarding must be enabled for uRPF to work.
- B. uRPF allows packets with source 0.0.0.0 and destination 255.255.255.255 to pass.
- C. Cisco Express Forwarding must be disabled for uRPF to work.
- D. uRPF configuration is supported on Layer 2 and Layer 3 Cisco devices.
- E. uRPF drops packets with source 0.0.0.0 and destination 255.255.255.255.
Answer: A,B
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_2/security/configuration/guide/fsecur_c/scfrpf.pdf
NEW QUESTION # 338
Refer to the exhibit.
A user cannot SSH to the router. What action must be taken to resolve this issue?
- A. Configure ip ssh source-interface loopback0
- B. Configure transport output ssh
- C. Configure ip ssh version 2
- D. Configure transport input ssh
Answer: D
Explanation:
Explanation
https://www.cisco.
com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/security/configuration_guide/b_sec_15
NEW QUESTION # 339
What is the minimum time gap required by the local system before putting a BFD control packet on the wire?
- A. Required Min Echo RX Interval
- B. Desired Min TX Interval
- C. Required Min RX Interval
- D. Detect Mult
Answer: B
Explanation:
Explanation
Desired Min TX Interval: This is the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets, less any jitterapplied. The value zero is reserved.
Required Min Echo RX Interval: This is the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting, less anyjitter applied by the sender. If this value is zero, the transmitting system does not support the receipt of BFD Echo packets.
NEW QUESTION # 340
Refer to the exhibit.
Which two actions restrict access to router R1 by SSH? (Choose two.)
- A. Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list
199 - B. Remove class-map ANY from service-policy CoPP
- C. Configure transport input ssh on line vty and remove sequence 30 from access list 100.
- D. Configure transport output ssh on line vty and remove sequence 20 from access list 100.
- E. Configure transport output ssh on line vty and remove sequence 10 from access list 199.
Answer: C,D
NEW QUESTION # 341
......
Latest 300-410 Exam Dumps Cisco Exam from Training: https://www.guidetorrent.com/300-410-pdf-free-download.html
Pass Cisco 300-410 PDF Dumps Recently Updated 563 Questions: https://drive.google.com/open?id=1foAz39u3mPZl5NOO5J9DTQbVfwaJMkoz