New Cisco 300-510 Dumps & Questions Updated on 2024
Dumps to Pass your 300-510 Exam with 100% Real Questions and Answers
NEW QUESTION # 101
Refer to the exhibit. After these configurations were applied to routers R1 and R2. the two devices cannot form a neighbor relationship. What is the reason tor the problem?
- A. The two routers have different IS-types
- B. The two routers cannot authenticate with one another
- C. The two routers have the same area ID.
- D. The two routers have the same network ID
Answer: D
Explanation:
For those asking about the password, area authentication doesn't prevent neighboring to come up because it is carried only in LSP, CSNP and PSNP messages and not in IIH messages.
https://www.cisco.com/c/en/us/support/docs/ip/integrated-intermediate-system-to-intermediate- system-is-is/13792-isis-authent.html
NEW QUESTION # 102
An engineer warns to map a multicast IP address to a multicast MAC.
How many bits are used to make the conversion?
- A. high-order 24 bits
- B. lower-order 24 bits
- C. higher-order 23 bits
- D. low order 23 bits
Answer: D
NEW QUESTION # 103
Refer to the exhibit.
XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed. Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?
- A. Option B
- B. Option C
- C. Option A
- D. Option D
Answer: D
NEW QUESTION # 104
Refer to the exhibit. The green policy is designed with low delay, and the pink policy is designed with low cost. What is the next hop for node A on its way to node D, with the objective of achieving a low delay?
- A. 192.168.3.6
- B. 192. 168.1.2
- C. 192.168.3.2
- D. 192.168.1.6
Answer: B
NEW QUESTION # 105
Refer to the exhibit.
The extension header of the IPv6 header is ignored when which value is equal to zero?
- A. Segments Left
- B. Hdr Ext Len
- C. Next Header
- D. Routing Type
Answer: C
NEW QUESTION # 106
Refer to the exhibit. A network operator is getting the route for 10.11.11 0/24 from two upstream providers on #XR3.
The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of 10.0.0.9 as primary when available.
Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?
- A. lower local preference on the prefix coming from 192.168.0.2
- B. weight of 100 on the prefix coming from 192.168.0.1
- C. higher local preference on the prefix coming from 192.168.0.1
- D. weight of 0 on the prefix coming from 192.168.0.2
Answer: D
Explanation:
Weight is the first attribute in path selection algorithm and is 0 for eBGP routes by default. If we set it to 0, router will continue from weight to the bottom, and when comparing neighbor router IDs it will find 192.168.0.1 less than 192.168.0.2 and the path will be selected as the best.
NEW QUESTION # 107
Refer to the exhibit. R21 is a multicast source sending multicast traffic 224.1.1.1 to R23, with RP22 serving as the rendezvous point inside AS65222. A network engineer noticed that when R21 goes down, R12 in AS65111 starts to send the same multicast group 224.1.1.1 through RP11. Which action resolves the issue?
- A. Advertise RP2 with a high local preference in AS65222.
- B. Block service groups 224.0.1.39 and 224.0.1.40 between the two autonomous systems.
- C. Disable PIM parse mode between RP11 and RP22 in the two autonomous systems.
- D. Enable passive interface under EIGRP between the two autonomous systems.
Answer: B
NEW QUESTION # 108
What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?
- A. tail-end router
- B. path computation engine
- C. SNMP server
- D. traffic controller
Answer: B
NEW QUESTION # 109
What is a requirement of PIM-SM?
- A. It must use an RP
- B. It requires OSPF to be configured on the network.
- C. It requires Cisco Express Forwarding to be enabled.
- D. It must be enabled on loopback interfaces only
Answer: A
NEW QUESTION # 110
Refer to the exhibit.
Refer to the exhibit There is a BGP traffic path issue between Customer-1 and Customer-2 Users from Customer-2 have reported file transfer issues High utilization on the path between both customers causes many packet drops. Which configuration resolves the issue?
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: B
NEW QUESTION # 111
Refer to the exhibit. R1 is sending data traffic to R6 using the same SRGB range as the other routers in the topology, but it is also using a non-default SRLB range. Which two configuration tasks must the engineer perform to enable normal SRGB and SRLB operations on this network?
(Choose two.)
- A. Set the default SRGB range to 16000 to 23999.
- B. Configure an adjacency SID from SRLB range 1002 to 6005.
- C. Configure router R2 with adjacency SID 4002 to enable it to reach R4.
- D. Configure router R1 with adjacency SID 1003 to enable it to reach R2.
- E. Set the SRGB range to 1002 to 6005.
Answer: A,B
NEW QUESTION # 112
Refer to the exhibit.
A service provider technician is working on a multicast issue for a customer. While checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.
Which factor might explain this issue?
- A. Only GLOP is permitted
- B. Only ASM is permitted
- C. Only the default SSM range is permitted
- D. Only the administratively scoped range is permitted
Answer: C
NEW QUESTION # 113
Refer to the exhibit.
An engineer is troubleshooting connectivity issues on the MPLS core network. A customer connected through R4 cannot reach the OSPF domain on R5. While checking the routing table of R1, the engineer cannot see all the routes from R3 and R5. Which task must the engineer perform so that R4 is able to reach R5?
- A. Enable OSPF peering and configure route redistribution between routers R4 and R1.
- B. Enable OSPF on the Area-0 routers and configure MP-BGP between routers R1 and R3.
- C. Enable route filtering between routers R1 and R3.
- D. Enable MP-BGP peering on routers R1. R3, R4, and R5.
Answer: A
NEW QUESTION # 114
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. weight
- B. MED
- C. local preference
- D. origin
Answer: B
NEW QUESTION # 115
Which difference must an engineer consider when choosing whether to implement OSPF or IS-IS as the routing protocol on the network?
- A. IS-IS supports ordinary, stub, totally-stub, and NSSA areas, but OSPF supports only stub areas.
- B. The OSPF DR election process is deterministic, and the IS-IS DS election process is not deterministic.
- C. IS-IS links are associated with either a Level 1 area or a Level 2 area at one time, but OSPF links are associated with multiple areas at one time.
- D. To support fast convergence, OSPF uses the LSA arrival timer and IS-IS uses the PRC-interval timer.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_isis/configuration/15-s/irs-15-s- book/irs-fscnt.html
NEW QUESTION # 116
......
Cisco 300-510 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
Updated Exam 300-510 Dumps with New Questions: https://www.guidetorrent.com/300-510-pdf-free-download.html
Today Updated 300-510 Exam Dumps Actual Questions: https://drive.google.com/open?id=1U7o_7XhVoy3WEMo2to7lbWFyMrstHBOg